The Anybus Communicator EtherCAT slave – PROFIBUS DP device is an industrial protocol gateway that allows you to seamlessly transfer data between PLC control systems over EtherCAT and PROFIBUS networks.
Anybus Communicators are designed to ensure reliable, secure, and high-speed data transfer between different industrial Ethernet and Fieldbus networks. Very easy to install and deploy, the stand-alone gateways enable transparent data exchange between PLCs, allowing you to integrate legacy equipment into modern, high-performance networks without any changes to the hardware and only minimal changes to the software.
Anybus Communicators are built using the award-winning and proven Anybus NP40 industrial network processor providing network conformance, high performance, and reliability. When connecting between PLCs on different networks, extremely fast data cycling is enabled with data transfer of up to 1500 bytes in each direction, meeting most current control application needs as well as supporting future demands.
Quick installation is ensured thanks to the intuitive configuration, easy-to-understand documentation, and smart hardware and housing design.
Excellent performance
Easy to Use
Latest Security Features
Designed for industrial environments
EtherCAT FEATURES
Dimensions (L x W x H) with serial and power connector | 98 x 27 x 144 mm 3.85 x 1.06 x 5,67 in |
Weight | 150 grams, 0.33 lb |
Buttons and switches | Reset button and security switch |
LEDs | Gateway, Network 1 & Network 2 |
IP rating | IP20 |
Housing material | PC ABS, UL 94 VO |
Mounting | DIN rail (35 * 7,5/15) |
Operating temperature | -25 to 70° C, -13 to 158° F |
Storage temperature | -40 to 85° C, -40 to 185° F |
Relative humidity | 0-95% non condensing |
Installation altitude | Up to 2 000 m |
Input voltage | 12 - 30 VDC |
Current consumption | Typical: 160 mA @ 24V Max: 400 mA @ 12V |
Power connector | 3-pin plug with screw terminal |
Protection | Reverse voltage protection and short circuit protection |
Ports | 2+2 x Ethernet |
Isolation | Galvanic isolation |
Bitrate | 10/100 Mbit full duplex |
Connector | RJ45 |
Switch. | Dual port cut-through switch |
Mode | EtherCAT slave according to IEC 61158 Type 12 (ETG.1000) |
Addressing modes | Logical, node, and position |
Synchronization modes | Free run |
Input data size | 1 486 bytes |
Output data size | 1 486 bytes |
Network redundancy | Device Level Ring (DLR), beacon-based |
Minimum cycle time | 100 μs |
Features | Supports CANopen over EtherCAT (CoE) |
ESI File | Available |
Mode | PROFIBUS DPV1 Device (slave) |
Input data size | 244 bytes |
Output data size | 244 bytes |
Baude rate | Automatic baud rate detection up to 12 Mbit/s |
Rotary switches | PROFIBUS slave address setting via onboard rotary switches or web interface |
Features | Supports Sync and Freeze and Watchdog |
I&M records | Manufacturer data (I&M0), Tag information (I&M1), Date/Time (I&M2), Description (I&M3) |
Connector | 1x D-sub 9-pin female PROFIBUS connector |
GSD | GSD file available |
UL | CULUSfile number E214107 |
CE | 2014/30/EU |
KC | R-R-ABJ-Communicator |
EMC |
EN 61000-6-2 |
Environment |
IEC 60068-2-1 Ab |
Vibration and shock |
IEC 60068-2-27 |
Waste certification | WEE |
Configuration software | Web based configuration |
Configuration ports | Dedicated 10/100 Mbit RJ45 Ethernet configuration port and Ethernet ports |
Secure boot | Ensures software authenticity |
Security switch | Physical switch that enable/disable access to the web based configuration interface |
Content | Gateway, power connector, start-up guide, compliance information sheet |
Box material | Cardboard |
MTBF | > 1500000 h, Telcordia Method I Case 3 at 30° C |